Gas solenoid valve type

Normally Closed Gas Solenoid Valve

A normally closed (NC) gas solenoid valve is shut when de-energised and only opens when the coil is powered. If power fails, the fan fails or an emergency stop is pressed, the valve closes and gas stops. This is the standard valve for commercial kitchen interlocks.

  • Fail-safe
  • Sizes from 15mm to large flanged
  • 230V and 24V coils

Quick answer

A normally closed (NC) gas solenoid valve is shut when de-energised and only opens when the coil is powered. If power fails, the fan fails or an emergency stop is pressed, the valve closes and gas stops. This is the standard valve for commercial kitchen interlocks.

Standards
BS 6173, IGEM/UP/19, IGEM/UP/11
In stock
Interlock panels, gas solenoid valves, air pressure switches
How to book
Call 020 8935 5572 or book online, 24/7

What is a normally closed gas solenoid valve?

A normally closed (NC) gas solenoid valve is shut when de-energised and only opens when the coil is powered. If power fails, the fan fails or an emergency stop is pressed, the valve closes and gas stops. This is the standard valve for commercial kitchen interlocks.

How it works

  • The coil is powered by the interlock panel.
  • Power lifts the plunger and opens the valve.
  • Removing power lets the spring close it.
  • Gas stays off until the panel is reset.

Typical uses

  • All commercial kitchen interlocks
  • Gas proving systems
  • Detection shut-off

Features

  • Fail-safe
  • Sizes from 15mm to large flanged
  • 230V and 24V coils
  • In stock for fast replacement

What we check

  • Valve closes on power loss
  • Tightness when closed
  • Coil resistance/temperature
  • Correct flow direction

Choosing the right valve size

Valve size is chosen from the total gas rate of every appliance and the supply pipe size. An undersized valve causes pressure drop, poor flames and nuisance flame-failure lockouts. We measure working pressure at the furthest appliance with everything running.

SizeTypical application
22mm (¾")Small cafés and takeaways
28mm (1")Most restaurants and pubs
35mm (1¼")Large restaurants and hotels
2" / 54mmCentral kitchens, plant rooms
Flanged DN50–DN150Large plant and industrial supplies

Supplied, installed and commissioned

Every normally closed gas solenoid valve we fit is installed by Gas Safe registered commercial catering engineers and commissioned to BS 6173 and IGEM/UP/19. Commissioning includes failing each fan in turn, testing the emergency stop, confirming the gas solenoid valve closes, and recording the results.

You receive a written commissioning record, and the system can be included in your annual CP42 commercial gas safety certificate inspection.

Parts carried in stock

  • Replacement gas interlock systems
  • Gas solenoid valves in common sizes
  • Air pressure switches
  • Quick release gas catering hoses
  • Super universal thermocouples

Repair, servicing and replacement

If your system stops resetting, keeps tripping or the gas will not come on, our engineers diagnose the fault on site. Most faults are a fan proving problem, a failed valve coil, an open emergency stop circuit or wiring disturbed during other work.

Annual servicing tests every safety function and is usually combined with the CP42 inspection to minimise disruption.

Regulations

BS 6173 requires gas supplies to commercial catering appliances to be interlocked with mechanical ventilation so appliances cannot operate without it. IGEM/UP/19 covers the design and application of interlock devices and CO₂ monitoring. The Gas Safety (Installation and Use) Regulations 1998 require installations to be maintained in a safe condition.

Compare gas solenoid valve types

TypeSummary
Normally Closed Gas Solenoid ValveCloses when power is lost — the fail-safe valve used on gas interlocks.
Normally Open Gas Solenoid ValveStays open without power and closes when energised — used in specific shut-off schemes.
Manual Reset Gas Solenoid ValveMust be reset by hand after closing, so gas cannot come back on by itself.
240V (230V) Gas Solenoid ValveMains-voltage coil — the most common coil on UK kitchen interlocks.
22mm (¾") Gas Solenoid ValveFor smaller kitchens and takeaways with a modest total gas load.
28mm (1") Gas Solenoid ValveThe most common commercial kitchen valve size.
35mm (1¼") Gas Solenoid ValveFor larger kitchens with higher gas loads.
2" (54mm) Gas Solenoid ValveLarge-bore valve for high-demand kitchens and plant rooms.
Flanged Gas Solenoid Valve (DN50–DN150)Flanged valves for large-bore commercial and industrial gas supplies.

From our engineers' vans

Photos from real jobs — the equipment described on this page, installed and serviced by our engineers.

New 2 inch gas solenoid valve ready for fitting
2" normally closed gas solenoid valve — in stock
New gas solenoid valve, product view
Replacement solenoid valves stocked for same-day fitting

Frequently asked questions

Why normally closed?

Because it fails safe — any power loss shuts the gas off.

Is it normal for the coil to get hot?

Warm is normal; too hot to touch or buzzing suggests a failing coil or wrong voltage.

Related guides

Parts in stock — ready to fit

Held in UK stock and carried on our vans, so most jobs are fixed in one visit.

  • Replacement gas interlock systems

    Complete panels & kits ready to fit

    In stock today

  • Air pressure switches

    Fan & gas proving pressure switches

    In stock today

  • Gas solenoid valves

    Normally closed safety shut-off valves

    In stock today

  • Quick release gas catering hoses

    Commercial ranges, bays & mobile catering

    In stock today

  • Super universal thermocouples

    Fits most commercial gas appliances

    In stock today

  • Need a part fitted?

    Same-day engineer dispatch with these parts on the van.

  • Gas Safe Registered

    Commercial catering & plant

  • 24/7 UK Response

    Same-day emergency dispatch

  • Vetted Engineers

    DBS checked for schools & care

  • Transparent Pricing

    Fixed callout, quoted parts

Call Us