Service guide
Gas Solenoid Valve Installation
Solenoid valve installation is notifiable commercial gas work. Position, orientation and pressure drop matter as much as the electrical connection to the interlock panel.
- Installed downstream of the emergency control valve, before appliance branches
- Accessible for manual reset without entering the canopy void
- Commissioned with tightness test and recorded trip times
Quick answer
Installing a gas solenoid valve means isolating the supply, fitting a correctly sized, normally-closed valve in the kitchen gas line, wiring it to the interlock or proving panel, then tightness-testing, purging and commissioning. It is Gas Safe registered work and usually takes a few hours.
- Typical time
- 2–4 hours
- Standards
- BS 6173, IGEM/UP/19, IGEM/UP/11
- In stock
- Interlock panels, gas solenoid valves, air pressure switches
- How to book
- Call 020 8935 5572 or book online, 24/7
Installation sequence
- Survey gas rate, pressure and pipe route; confirm valve DN and coil voltage
- Isolate and purge the section in line with IGEM procedures
- Fit the valve with the flow arrow correct and coil upright, supported independently of the pipework
- Run the coil cable in appropriate containment away from hot surfaces back to the control panel
- Fit or verify emergency stop buttons on escape routes
- Tightness test, purge and relight all appliances
- Functional test every trip path and record closure times
Common installation defects
- Valve installed against the flow arrow or with the coil horizontal
- Undersized valve causing pressure drop and appliance under-firing
- Valve buried above a canopy with no access for manual reset
- Coil cable in unsuitable flex, chafing on ductwork
- No tightness test record or commissioning certificate issued
From our engineers' vans
Photos from real jobs — the equipment described on this page, installed and serviced by our engineers.


Frequently asked questions
How does a gas solenoid valve work?
When voltage reaches the coil, a magnetic field lifts the plunger off its seat and gas flows. When the voltage is removed, a spring returns the plunger and seals the valve. Most kitchen valves are normally-closed and 230V AC.
How do you test a gas solenoid valve?
A Gas Safe engineer checks the coil voltage and resistance, confirms the valve opens and closes on command from the panel, and carries out a let-by and tightness test to prove the valve seals fully when closed.
Where should the solenoid valve be fitted?
Downstream of the emergency control valve and upstream of appliance branch connections, in an accessible, ventilated position.
Does solenoid valve installation need certifying?
Yes — it is part of the gas safety system and must be commissioned, tested and recorded by a Gas Safe registered commercial engineer.
Related guides
Gas Solenoid Valves
Normally closed automatic shut-off valves and diagnostics.
Solenoid Valve Replacement
When to replace, like-for-like sizing and recommissioning.
Gas Interlock Systems
Installation, servicing, testing and fault-finding for kitchen ventilation interlocks.
Gas Safety Control Panels
Interlock and proving panels, indicators and diagnostic codes.
Commercial Kitchen Gas Safety
Ventilation interlock, airflow proving and CP42 compliance.
Sensors & Controls
Air pressure switches, airflow sensors, current monitors, e-stops.
Parts in stock — ready to fit
Held in UK stock and carried on our vans, so most jobs are fixed in one visit.
Replacement gas interlock systems
Complete panels & kits ready to fit
In stock today
Air pressure switches
Fan & gas proving pressure switches
In stock today
Gas solenoid valves
Normally closed safety shut-off valves
In stock today
Quick release gas catering hoses
Commercial ranges, bays & mobile catering
In stock today
Super universal thermocouples
Fits most commercial gas appliances
In stock today
Need a part fitted?
Same-day engineer dispatch with these parts on the van.
Gas Safe Registered
Commercial catering & plant
24/7 UK Response
Same-day emergency dispatch
Vetted Engineers
DBS checked for schools & care
Transparent Pricing
Fixed callout, quoted parts
