Service
Gas Interlock Servicing & Annual Testing
An interlock is a safety system, so it has to be proved rather than assumed. Our annual test demonstrates that gas actually shuts off when ventilation fails — and gives you the record an inspector will ask for.
- Documented fan fail, emergency stop and valve closure testing
- Air pressure switch and airflow sensor checked and reset to specification
- Planned maintenance contracts across UK commercial sites
Quick answer
A gas interlock service tests that the system still shuts off the gas when ventilation fails. The engineer checks each airflow sensor, the solenoid valve for let-by, the emergency stops, the panel and its wiring, and records the results. Annual servicing, usually alongside the CP42 inspection, is recommended.
- Frequency
- At least every 12 months
- Standards
- BS 6173, IGEM/UP/19, IGEM/UP/11
- Paperwork
- Service and test record
- How to book
- Call 020 8935 5572 or book online, 24/7
What the annual test covers
- Visual inspection of panel, valve, sensors and cabling for damage, grease ingress and corrosion
- Fan fail simulation — gas must shut off within seconds of ventilation loss
- Emergency stop operation and reset procedure verified
- Air pressure switch setting checked against extract performance, adjusted and locked
- Solenoid valve closure and tightness test; coil current and temperature check
- Gas detection and CO/CO₂ inputs function tested where fitted
- Labelling, reset instructions and staff walkthrough
- Certificate and test record issued
Why interlocks drift out of specification
Extract filters block, fan belts slip, ductwork fills with grease and make-up air grilles get covered. The pressure the switch sees changes, and the interlock either nuisance trips or — worse — proves ventilation that is no longer adequate. Regular cleaning of the canopy and filters directly affects interlock reliability.
How the work is carried out
Every job starts with a proper look at the site rather than a guess over the phone. The engineer confirms the gas supply size and pressure, the appliances on the line, the ventilation arrangement and the position of the existing or proposed control panel. From that survey the correct solenoid valve size, proving devices and panel are selected, and you get a fixed written quotation before any work begins.
On the day, the gas supply is isolated and the work is carried out by a Gas Safe registered engineer holding the relevant commercial catering qualifications. Pipework alterations are made to current standards, the interlock wiring is installed and labelled, and the whole system is then commissioned: the fans are started, the proving is checked, the emergency stops are tested, and the gas is only released once every safety function works exactly as it should.
You are left with a working system, a demonstration for your staff, and the paperwork — a commissioning record and test certificate that go straight into your gas safety file for insurers, landlords and environmental health.
Parts and equipment we use
We fit proven commercial-grade equipment rather than the cheapest available parts, because an interlock that nuisance-trips or fails early costs a kitchen far more in lost trading than it saves on the invoice. Panels from the established UK manufacturers are all supplied, wired and commissioned by our engineers.
Solenoid valves are normally closed, power-to-open safety shut-off valves sized to the pipework, from 22mm and 28mm on smaller lines up to flanged valves on large range supplies. Airflow proving is matched to the ventilation: differential air pressure switches across the fans, or current sensors where pressure tapping is impractical.
The common failure items — replacement interlock panels, gas solenoid valves, air pressure switches, quick-release catering hoses and universal thermocouples — are carried in stock on the van, which is why most repairs and replacements are completed in a single visit.
Areas we cover
Our engineers cover the whole of London, Surrey and the M25 corridor, including the City and West End, the inner and outer London boroughs, Kingston, Epsom, Guildford, Woking and the Surrey towns, and the Home Counties belt through Watford, St Albans, Slough, Sevenoaks and the Dartford crossing area.
Planned work is booked to suit your trading hours — early mornings, evenings, nights and weekends are all available for kitchens that cannot close during service. Emergency call-outs for kitchens with no gas are attended the same day wherever possible, and out-of-hours access, permits and risk assessments are handled for managed sites and shopping centres.
Frequently asked questions
How often should a gas interlock be serviced?
At least once a year, and after any change to the ventilation or gas installation. Many kitchens combine it with their annual CP42 gas safety inspection.
How does a gas interlock system work?
Air pressure switches or current sensors prove the ventilation fans are running. The interlock panel then opens a normally-closed gas solenoid valve. If a fan stops, a sensor fails or the emergency stop is pressed, the panel removes power from the valve and the gas closes.
Can the interlock test be done with my gas safety inspection?
Yes, and it is the efficient option — one visit, one set of paperwork.
How long does the test take?
Typically 45–90 minutes for a single-zone kitchen system, longer for multi-zone sites or where faults are found.
What if it fails?
We report the defect, isolate gas if it is unsafe, and quote the repair. Common failures — pressure switch, solenoid coil, e-stop — are usually fixed from van stock the same day.
Are your engineers Gas Safe registered for commercial catering?
Yes. All gas work is carried out by Gas Safe registered engineers holding the commercial catering categories needed for kitchen appliances, pipework and interlock systems. Registration details are available on request and shown on the engineer's ID card on site.
Can you work outside our opening hours?
Yes. Most of our commercial kitchen work is planned around service — early mornings, evenings, overnight and weekends — so the kitchen stays open when it needs to be. Out-of-hours working is quoted as part of the job, not as a surprise extra.
Related guides
Gas Interlock Systems
The pillar guide: how interlocks work, standards and fault-finding.
Repair & Emergency
Interlock not working or tripping — same-day engineer attendance.
Regulations & Law
BS 6173, IGEM/UP/19 and whether an interlock is a legal requirement.
Sensors & Controls
Air pressure switches, airflow sensors, current monitors, e-stops.
Commercial Kitchen Gas Safety
Ventilation interlock, airflow proving and CP42 compliance.
Parts in stock — ready to fit
Held in UK stock and carried on our vans, so most jobs are fixed in one visit.
Replacement gas interlock systems
Complete panels & kits ready to fit
In stock today
Air pressure switches
Fan & gas proving pressure switches
In stock today
Gas solenoid valves
Normally closed safety shut-off valves
In stock today
Quick release gas catering hoses
Commercial ranges, bays & mobile catering
In stock today
Super universal thermocouples
Fits most commercial gas appliances
In stock today
Need a part fitted?
Same-day engineer dispatch with these parts on the van.
Gas Safe Registered
Commercial catering & plant
24/7 UK Response
Same-day emergency dispatch
Vetted Engineers
DBS checked for schools & care
Transparent Pricing
Fixed callout, quoted parts
