Service

Gas Interlock Replacement Systems

If your interlock panel is obsolete, water damaged or unsupported, replacing it is faster and cheaper than chasing spares. We hold replacement interlock systems, pressure switches and valves in stock.

  • Complete replacement interlock systems in stock today
  • Like-for-like swaps reusing existing cable routes where possible
  • Recommissioned, tested and certified after replacement

Quick answer

Replace a gas interlock panel when it is obsolete, repeatedly failing, missing gas proving or no longer meets BS 6173. A replacement panel can usually reuse sound sensors, valves and wiring, so most swaps take half a day and are commissioned and certified on the same visit.

Typical time
Half a day for a like-for-like panel
Standards
BS 6173, IGEM/UP/19, IGEM/UP/11
In stock
Interlock panels, gas solenoid valves, air pressure switches
How to book
Call 020 8935 5572 or book online, 24/7

When replacement is the right call

  • Manufacturer no longer supplies boards, relays or coils for your panel
  • Grease or water ingress has corroded the panel internals
  • The system pre-dates current standards or has no proving on make-up air
  • The kitchen has been extended or appliances added, so the valve is now undersized
  • Repeated nuisance trips traced to a failing controller rather than ventilation

What a replacement involves

We survey the existing installation, confirm valve sizing against the current appliance gas rate, and select an equivalent current system from stock. Existing containment and cabling is reused where it is sound, which keeps disruption and cost down. The system is then commissioned and certified from scratch.

Stock parts

  • Replacement gas interlock systems
  • Air pressure switches (fan and gas proving)
  • Gas solenoid valves, normally closed, 28mm to 54mm equivalents
  • Quick release gas catering hoses
  • Super universal thermocouples

How the work is carried out

Every job starts with a proper look at the site rather than a guess over the phone. The engineer confirms the gas supply size and pressure, the appliances on the line, the ventilation arrangement and the position of the existing or proposed control panel. From that survey the correct solenoid valve size, proving devices and panel are selected, and you get a fixed written quotation before any work begins.

On the day, the gas supply is isolated and the work is carried out by a Gas Safe registered engineer holding the relevant commercial catering qualifications. Pipework alterations are made to current standards, the interlock wiring is installed and labelled, and the whole system is then commissioned: the fans are started, the proving is checked, the emergency stops are tested, and the gas is only released once every safety function works exactly as it should.

You are left with a working system, a demonstration for your staff, and the paperwork — a commissioning record and test certificate that go straight into your gas safety file for insurers, landlords and environmental health.

Parts and equipment we use

We fit proven commercial-grade equipment rather than the cheapest available parts, because an interlock that nuisance-trips or fails early costs a kitchen far more in lost trading than it saves on the invoice. Panels from the established UK manufacturers are all supplied, wired and commissioned by our engineers.

Solenoid valves are normally closed, power-to-open safety shut-off valves sized to the pipework, from 22mm and 28mm on smaller lines up to flanged valves on large range supplies. Airflow proving is matched to the ventilation: differential air pressure switches across the fans, or current sensors where pressure tapping is impractical.

The common failure items — replacement interlock panels, gas solenoid valves, air pressure switches, quick-release catering hoses and universal thermocouples — are carried in stock on the van, which is why most repairs and replacements are completed in a single visit.

Areas we cover

Our engineers cover the whole of London, Surrey and the M25 corridor, including the City and West End, the inner and outer London boroughs, Kingston, Epsom, Guildford, Woking and the Surrey towns, and the Home Counties belt through Watford, St Albans, Slough, Sevenoaks and the Dartford crossing area.

Planned work is booked to suit your trading hours — early mornings, evenings, nights and weekends are all available for kitchens that cannot close during service. Emergency call-outs for kitchens with no gas are attended the same day wherever possible, and out-of-hours access, permits and risk assessments are handled for managed sites and shopping centres.

Frequently asked questions

Do I need a gas interlock system?

Yes, in almost every commercial kitchen with mechanical extraction. BS 6173 requires gas supply to catering appliances to be interlocked with the ventilation system, and a Gas Safe engineer will normally record a missing interlock as a defect on a CP42 inspection.

Is a gas interlock system a legal requirement?

The Gas Safety (Installation and Use) Regulations require gas installations to be safe; BS 6173 is the recognised standard that sets out how, and it requires a ventilation interlock where mechanical extraction is installed. Insurers and environmental health officers enforce it in practice.

Can I keep my existing solenoid valve?

Often yes, if it is the correct size, closes cleanly and passes a tightness test. We check it as part of the swap rather than replacing parts unnecessarily.

How long is the kitchen down?

A like-for-like panel replacement is usually a few hours with gas off only for the valve work. We can work overnight to avoid closing.

Do you replace interlocks you didn't install?

Yes — most of our replacement work is on systems fitted by others.

Are your engineers Gas Safe registered for commercial catering?

Yes. All gas work is carried out by Gas Safe registered engineers holding the commercial catering categories needed for kitchen appliances, pipework and interlock systems. Registration details are available on request and shown on the engineer's ID card on site.

Can you work outside our opening hours?

Yes. Most of our commercial kitchen work is planned around service — early mornings, evenings, overnight and weekends — so the kitchen stays open when it needs to be. Out-of-hours working is quoted as part of the job, not as a surprise extra.

Related guides

Parts in stock — ready to fit

Held in UK stock and carried on our vans, so most jobs are fixed in one visit.

  • Replacement gas interlock systems

    Complete panels & kits ready to fit

    In stock today

  • Air pressure switches

    Fan & gas proving pressure switches

    In stock today

  • Gas solenoid valves

    Normally closed safety shut-off valves

    In stock today

  • Quick release gas catering hoses

    Commercial ranges, bays & mobile catering

    In stock today

  • Super universal thermocouples

    Fits most commercial gas appliances

    In stock today

  • Need a part fitted?

    Same-day engineer dispatch with these parts on the van.

  • Gas Safe Registered

    Commercial catering & plant

  • 24/7 UK Response

    Same-day emergency dispatch

  • Vetted Engineers

    DBS checked for schools & care

  • Transparent Pricing

    Fixed callout, quoted parts

Call Us